About Goodwin Appliance Washer Dryer Repair
Honolulu washer and dryer repair specialist with 14 years experience. 4.8 stars with 405 Yelp reviews. Family-owned with flat-rate pricing.
The directory record lists 3 services across 2 appliance types and names 8 brands. It is listed as both licensed and insured, established in 2012, and states a service area covering Honolulu and Oahu.
The record carries no email address and no website. A blank field means the source it was compiled from did not publish that detail — not that the company lacks it. Ask on the phone about anything that matters to your job.
Everything stated about Goodwin Appliance Washer Dryer Repair on this page comes from that record. The repair costs, part prices, and fault descriptions below are national reference figures for the appliances the company lists — useful for sanity-checking a quote, but not prices Goodwin Appliance Washer Dryer Repair has published.
Hours
- Mon–Fri
- 7:00 AM - 7:00 PM
- Saturday
- 7:00 AM - 1:00 PM
- Sunday
- Closed
Service area
- Honolulu
- Oahu
Services offered
Listed in Goodwin Appliance Washer Dryer Repair's own words.
- Washer Repair
- Dryer Repair
- Appliance Installation
Appliances serviced, and what those repairs cost
Goodwin Appliance Washer Dryer Repair lists 2 of the twelve appliance types in this directory. Each row links to the full repair reference for that appliance and carries four national figures: the diagnostic visit, the typical all-in repair, what a comparable new unit costs, and how long the appliance is expected to last.
| Appliance | Diagnostic | Typical repair | New unit | Avg. life |
|---|---|---|---|---|
| Washer repair | $50–$100 | $150–$350 | $800 | 11 yrs |
| Dryer repair | $50–$100 | $100–$350 | $750 | 12 yrs |
These are national bands, not quotes for Honolulu, HI. Labor rates track local wages, insurance, and drive time, so the same job costs measurably more in a dense, high-cost metro than in a smaller market, while the part itself costs roughly the same anywhere. Sealed-system refrigerant work, built-in installations, and luxury brands sit at the top of every range because fewer technicians are certified for them and parts are ordered rather than stocked. Get two or three quotes before you commit.
A quote is worth checking against the appliance's remaining value. The rule of thumb built into our value estimator: replace rather than repair once the quote passes about half the price of a comparable new unit and the appliance is past roughly two-thirds of its expected service life. Under both thresholds, repair is almost always the cheaper decision.
Brands serviced, and what each tier means
Goodwin Appliance Washer Dryer Repair names 8 brands. Price tier decides more about a repair than the badge does: it sets what a part costs, where it comes from, and whether a general technician can buy it at all.
The best-stocked parts situation in the trade. OEM components are easy to source, aftermarket equivalents exist for most of them, and a technician will often have the common failure on the van rather than ordering it.
Any qualified technician can take the job. Factory-authorised service mainly matters while the machine is still in its warranty period — outside it, an experienced independent is usually faster and cheaper.
OEM parts cost noticeably more and the aftermarket is thinner, so expect an order-and-return visit on anything past the common failures. Because the machine is worth more, a part that would total a budget unit is often still the right call here.
Most independent technicians work on this tier, but ask whether they have had factory training on the line. Control boards, inverter drives and door mechanisms diverge enough between premium platforms that experience is not interchangeable.
Common faults on the appliances they service
Symptom, the cause it most often turns out to be, and whether it is homeowner work or a job that has to go to a technician. Knowing which one you probably have before you call shortens the visit — and sometimes removes the need for one.
- Homeowner fix
- Safe for a homeowner with basic tools once the appliance is unplugged or the breaker is off.
- Technician
- Needs a technician — meter diagnosis, a model-matched part, or teardown that is easy to get wrong.
- Washer
Fills and washes but will not drain
Homeowner fixA blocked pump filter, a kinked drain hose, or a seized drain pump. On front-loaders the filter behind the lower access panel is the first place to look and is free to clear.
Step-by-step: Washer Won't Drain - Dryer
Tumbles but produces no heat at all
TechnicianA blown thermal fuse — usually triggered by a restricted vent — or a failed heating element on an electric machine, or an igniter on a gas one.
Step-by-step: Dryer Not Heating - Washer
Drains but will not spin
TechnicianA failed lid switch or door lock on a top-loader, or a stretched drive belt and worn motor coupler on a direct-drive machine.
Step-by-step: Washer Won't Spin - Dryer
Heats but clothes take two or three cycles to dry
Homeowner fixA crushed, kinked or lint-packed vent line, or a blocked exterior flap. Airflow, not heat, is the limiting factor.
Step-by-step: Dryer Takes Too Long - Washer
Walks across the floor or bangs hard on spin
TechnicianWorn suspension rods or shock absorbers letting the tub swing, or shipping bolts that were never removed at installation.
Step-by-step: Washer Shaking and Walking - Dryer
Loud rumbling, thumping, or a rhythmic squeal
TechnicianWorn drum rollers, a failing idler pulley, or a glazed drive belt. All are wear parts and are usually replaced together.
Step-by-step: Dryer Squealing or Thumping - Washer
Water on the floor after every cycle
TechnicianOn a front-loader, a split or mouldy door boot seal. On a top-loader, the tub-to-pump hose or the inlet valve behind the machine.
Step-by-step: Washer Leaking Water - Dryer
Will not start, no sound at all
TechnicianThe door switch, the start switch, or a thermal cut-off on the heater circuit. Door switches fail from thousands of open-close cycles.
Step-by-step: Dryer Won't Start - Washer
Roaring or grinding that gets louder as the spin speeds up
TechnicianRear tub bearings. This is the one washer fault that regularly costs more than the machine is worth on a mid-market model.
- Dryer
Cabinet or laundry room gets very hot during a cycle
TechnicianThe vent is discharging into the room, or the cycling thermostat has failed closed. Treat this as urgent — it is the classic pre-fire condition.
Step-by-step: Dryer Takes Too Long
Try it yourself first
Free step-by-step guides for the same appliances Goodwin Appliance Washer Dryer Repair services, each one stating the DIY cost against the pro cost — because the honest answer to "should I fix this myself" is usually visible in that gap.
Washer
Washer Won't Drain — Work the Blockage Path in Order
A washer that will not drain has a blockage somewhere along a short, entirely traceable path: tub, sump, tub-to-pump hose, pump, drain hose, standpipe, house drain. The mistake almost everyone makes is buying a pump first. Work the path in physical order from the drum outward, and in most cases you will find a sock or a handful of lint long before you reach anything electrical. Start by getting the standing water out, because you cannot inspect anything until the tub is empty.
- DIY
- $0–$130
- Pro
- $150–$400
- Time
- 45–90 minutes
Dryer
Dryer Not Heating — Electric and Gas, Diagnosed in Order
A dryer that tumbles happily but leaves clothes cold and wet has lost its heat source, and the diagnosis splits immediately on fuel type. On an electric dryer, the two things worth checking before you open the cabinet are the cycle setting and whether the machine is still receiving both of its 240-volt legs — between them they account for a great many no-heat calls and neither costs anything. On a gas dryer, the ignition sequence is visible through the burner opening, and watching one cycle tells you which of three parts has failed. Work through the shared checks first, then take the branch that matches your machine.
- DIY
- $5–$70
- Pro
- $150–$400
- Time
- 45–120 minutes
Washer
Washer Won't Spin — Diagnostic Guide
A washer that fills and washes but leaves the load sopping wet has a spin fault, and the cause falls into one of three buckets: the machine is refusing to spin on purpose, something in the drive train has broken, or it cannot drain and therefore will not spin. Work in that order — the safety-interlock causes are free to check and account for most of these failures.
- DIY
- $0–$120
- Pro
- $150–$600
- Time
- 30–90 minutes
Dryer
Dryer Takes Too Long — Restore Full Drying Speed
A dryer that used to finish in 45 minutes and now needs two cycles has not lost heat — it has lost airflow. Drying works by moving hot air through the clothes and carrying the moisture outside, and every restriction in that path halves the machine's effectiveness while driving up the run time, the power bill, and the fire risk. Nine times out of ten this is a vent problem, and it is free to fix.
- DIY
- $0–$80
- Pro
- $100–$350
- Time
- 45–120 minutes
Washer
Washer Leaking Water — Trace the Leak, Then Fix It
Finding a washer leak is entirely about timing. A machine leaks at one specific point in the cycle, and which point tells you which component. Run a short cycle with the machine pulled out and a flashlight in hand, and watch — the ten minutes you spend observing will save you from replacing parts that were never the problem.
- DIY
- $15–$150
- Pro
- $150–$600
- Time
- 30–90 minutes
Dryer
Dryer Squealing or Thumping — Find the Worn Part
Dryers are mechanically simple, which is good news: there are only about five things that make noise, and each one makes a distinct sound. A steady squeal that rises with the drum is a roller or the idler pulley. A rhythmic thump once per drum revolution is a belt or a flat-spotted roller. A metallic scrape is the drum contacting the bulkhead. A rattle that comes and goes is something in the blower. Identify the sound first, then open the machine once.
- DIY
- $25–$80
- Pro
- $150–$350
- Time
- 60–150 minutes
What the parts cost
The components that most often fail on these appliances, with typical retail prices for the part alone. Labor is not included, and these are not this company's prices — they are what a homeowner pays a parts retailer, so you can see how much of a quote is part and how much is labor.
| Part | Appliance | Typical price | Fitting |
|---|---|---|---|
| Drain Pump | Washer | $30–$80 | Moderate |
| Thermal Fuse | Dryer | $5–$20 | Easy |
| Lid Switch | Washer | $15–$40 | Easy |
| Heating Element | Dryer | $20–$60 | Moderate |
| Door Lock Assembly | Washer | $40–$140 | Moderate |
| Cycling and High-Limit Thermostats | Dryer | $10–$40 | Easy |
| Drive Belt | Washer | $15–$50 | Moderate |
| Drive Belt | Dryer | $12–$45 | Moderate |
| Water Inlet Valve | Washer | $25–$85 | Moderate |
| Drum Rollers and Idler Pulley | Dryer | $20–$70 | Moderate |
| Shock Absorbers and Suspension Rods | Washer | $30–$100 | Moderate |
| Gas Igniter | Dryer | $20–$65 | Moderate |
A part that costs $30 inside a $250 quote is normal — the rest is the trip, the diagnosis, and the labor. A part that costs $300 is the point at which the repair-or-replace question is worth asking properly. Ask for the part figure and the labor figure separately on any written estimate.
What the company highlights
Claims from the company's own listing, reproduced as published. We have not verified them — treat anything that matters to your job as a question to ask on the phone.
- 4.8 stars with 405 Yelp reviews
- Washer and dryer specialist
- Family-owned with flat rate $200 + parts
Certifications
As stated in the record. Ask to see current documentation before work begins — certifications can lapse between directory updates.
- Certified Professionals
Questions to ask Goodwin Appliance Washer Dryer Repair before you book
The record lists Goodwin Appliance Washer Dryer Repair as licensed and insured, and names 1 certification. That is what the source published, not something we verified — so the checks below still apply.
Ask for the license number, then verify it yourself
There is no single national appliance repair license. Requirements are set state by state, and in some places by the city or county, so the only reliable check is the paperwork. Ask which license or registration the company works under, get the number, and confirm it is active with the authority that issued it before you book.
Get proof of liability insurance, not a verbal assurance
A technician works on your water lines, your gas line, and your electrical circuits. Ask for a current certificate of general liability insurance in the company's name and check that the policy is in force on the day of the visit. A company that carries it will send the certificate without hesitating.
Require EPA certification for any sealed-system work
Section 608 of the federal Clean Air Act requires EPA certification for anyone who opens a sealed refrigerant system. That covers refrigerators, freezers, ice makers, and wine coolers. If a quote involves recovering, recharging, or brazing refrigerant lines, ask to see the certification before the work starts.
Separate the diagnostic fee from the estimate
Most shops charge a service-call or diagnostic fee to send a technician out, and many credit it toward the repair if you go ahead. Ask what the fee is and whether it is credited, then ask for a written estimate that itemizes parts, labor, and any trip charge before you authorize the job.
Put the warranty term on the estimate
Parts and labor are usually guaranteed for different lengths of time and the terms vary by company, so ask for both in writing rather than assuming. Ask specifically who pays for the return visit if the same fault comes back within the term.
Pay on completion, and keep the itemized invoice
A deposit against a special-order part is normal; a large up-front payment for the whole job is not. Pay the balance once the appliance has been tested in front of you, and keep the itemized invoice — you will need the part number and the labor term for any warranty claim later.
Have this ready when you call
For washer work specifically, these are the answers that decide which parts get loaded on the van — and whether the first visit is the only visit.
- Top-loader or front-loader, and the model number from the door rim or the back panel.
- The exact error code, if the display shows one.
- Whether the drum spins freely by hand when the machine is off.
- Whether water is left standing in the drum at the end of the cycle.
- Whether the noise happens on wash, on spin, or on both.
How Goodwin Appliance Washer Dryer Repair compares in Honolulu
Measured against the 8 appliance repair companies listed in Honolulu. Every figure below is read from the same records — a dash means the company did not state that detail, not that the answer is zero.
| Measure | This company | Honolulu average |
|---|---|---|
| Customer rating | 4.8 | 4.6 |
| Reviews | 405 | 118 |
| Year established | 2012 | 2011 |
| Brands serviced | 8 | 7.8 |
| Appliance types | 2 | 4.8 |
By customer rating, Goodwin Appliance Washer Dryer Repair ranks 1 of 7 among the Honolulucompanies that carry a rating. A high average on a handful of reviews is not the same signal as a slightly lower one on hundreds, so read the rating and the review count together — both are in the table above.
7 of the 8 Honolulu companies state a license, and none list a 24/7 emergency line. Across the whole directory, 676 of 873 listed companies state a license and the average rating is 4.6 out of 5 — the national numbers to hold this city’s average against.
Location
Goodwin Appliance Washer Dryer Repair lists this address. Many appliance repair companies work out of a van and a yard rather than a shop counter, so call before visiting.
Helpful resources
Appliance reference
Appliance blue book