Appliance repair in Texarkana, TX

Rating shows the score followed by the review count. A dash means the business did not state that detail — confirm directly before booking.

A repair bill in Texarkana has two parts. The first is the diagnostic or service-call fee — $40–$130 depending on the appliance — which many shops credit toward the job if you go ahead. The second is the repair itself, from $50–$600 once parts and labor are counted. Ask for both numbers separately before you authorize anything.

Diagnosis first

What local pros actually do

A clear diagnosis saves time

Texas technicians list everything from routine maintenance to control-board diagnosis. Ask what they found, what the part costs, and whether the repair is covered by a warranty.

Diagnostic and repair figures are national ranges, not quotes. New-unit prices and service life are the averages behind our appliance value estimator. The pro count is the number of listed companies here that name that appliance.

These are national bands, not quotes for Texarkana, TX. Labor rates track local wages, insurance, and drive time, so the same job costs measurably more in a dense, high-cost metro than in a smaller market, while the part itself costs roughly the same anywhere. Sealed-system refrigerant work, built-in installations, and luxury brands sit at the top of every range because fewer technicians are certified for them and parts are ordered rather than stocked. Get two or three quotes before you commit.

A quote is worth checking against the appliance's remaining value. The rule of thumb built into our value estimator: replace rather than repair once the quote passes about half the price of a comparable new unit and the appliance is past roughly two-thirds of its expected service life. Under both thresholds, repair is almost always the cheaper decision.

A meaningful share of service calls are resolved by something a homeowner can check first: a clogged dryer vent, a blocked washer pump filter, dust-caked condenser coils, a spray arm full of debris. Work through the relevant guide before you book — if it does not resolve it, you will at least be able to describe the symptom precisely, which is what gets the right technician and the right part on the first visit.

• Dryer

  Dryer Not Heating — Electric and Gas, Diagnosed in Order

  A dryer that tumbles happily but leaves clothes cold and wet has lost its heat source, and the diagnosis splits immediately on fuel type. On an electric dryer, the two things worth checking before you open the cabinet are the cycle setting and whether the machine is still receiving both of its 240-volt legs — between them they account for a great many no-heat calls and neither costs anything. On a gas dryer, the ignition sequence is visible through the burner opening, and watching one cycle tells you which of three parts has failed. Work through the shared checks first, then take the branch that matches your machine.

  DIY

  $5–$70

  Pro

  $150–$400

  Time

  45–120 minutes

• Refrigerator

  Refrigerator Not Cooling — Narrow It Down Before You Buy Parts

  A refrigerator that has stopped cooling is not one fault but a family of them, and the fastest way to narrow it is to look at the freezer before the fridge. If both compartments are warm, the problem is in the machinery that makes cold — power, the condenser, the compressor circuit. If the freezer is still making ice but the fresh food section has gone warm, the cold is being made and not delivered, which points at airflow rather than refrigeration. Everything below is ordered so the free checks come first and the expensive conclusions last.

  DIY

  $0–$150

  Pro

  $150–$900

  Time

  45–90 minutes

• Washer

  Washer Won't Drain — Work the Blockage Path in Order

  A washer that will not drain has a blockage somewhere along a short, entirely traceable path: tub, sump, tub-to-pump hose, pump, drain hose, standpipe, house drain. The mistake almost everyone makes is buying a pump first. Work the path in physical order from the drum outward, and in most cases you will find a sock or a handful of lint long before you reach anything electrical. Start by getting the standing water out, because you cannot inspect anything until the tub is empty.

  DIY

  $0–$130

  Pro

  $150–$400

  Time

  45–90 minutes

• Oven & Range

  Oven Not Heating Evenly — Map the Problem Before You Fix It

  Uneven baking and a miscalibrated oven are two different faults that get reported with the same words, so the first job is to tell them apart. An oven that is simply running cool or hot everywhere at once needs calibrating and nothing else. An oven that browns one corner of a tray and leaves the opposite corner pale has an airflow, element or door problem, and no amount of offset adjustment will help. Twenty minutes with a slice of bread will tell you which one you have, and that determines everything that follows.

  DIY

  $0–$80

  Pro

  $150–$400

  Time

  45–90 minutes plus preheat time

• Dishwasher

  Dishwasher Not Cleaning — Find Out What It Is Short Of

  A dishwasher cleans with four things: hot water, enough of it, spray pressure, and detergent that gets released at the right moment. When dishes come out gritty, one of those four is missing, and the job is to work out which. Be precise about the symptom first, because it points at different faults — food particles left stuck on is a spray or filter problem, a chalky white haze is a water hardness and rinse aid problem, and food redeposited as a fine grey film across everything is a filter or drain problem. This guide covers the first of those.

  DIY

  $0–$70

  Pro

  $120–$400

  Time

  30–60 minutes

• Microwave

  Microwave Runs But Doesn't Heat — What You Can Safely Check

  A microwave that lights up, turns the tray and counts down but leaves food cold has a fault in the high-voltage section — the magnetron, the diode, the capacitor, or the transformer. This is the one common appliance repair where the honest advice is that most of it is not a DIY job. The capacitor inside holds thousands of volts after the plug is out, and it does not care that you were careful. This guide covers what you can safely check and where to stop.

  DIY

  $0

  Pro

  $150–$400

  Time

  15–30 minutes for safe checks

This directory publishes what each company states about itself and links straight to its own phone number — we do not sell leads and we do not vet anyone on your behalf. The verification below is yours to do, and it is the same in Texas as anywhere else: confirm the paperwork, then confirm the price, in that order.

1. 01

   Ask for the license number, then verify it yourself

   There is no single national appliance repair license. Requirements are set state by state, and in some places by the city or county, so the only reliable check is the paperwork. Ask which license or registration the company works under, get the number, and confirm it is active with the authority that issued it before you book.

2. 02

   Get proof of liability insurance, not a verbal assurance

   A technician works on your water lines, your gas line, and your electrical circuits. Ask for a current certificate of general liability insurance in the company's name and check that the policy is in force on the day of the visit. A company that carries it will send the certificate without hesitating.

3. 03

   Require EPA certification for any sealed-system work

   Section 608 of the federal Clean Air Act requires EPA certification for anyone who opens a sealed refrigerant system. That covers refrigerators, freezers, ice makers, and wine coolers. If a quote involves recovering, recharging, or brazing refrigerant lines, ask to see the certification before the work starts.

4. 04

   Separate the diagnostic fee from the estimate

   Most shops charge a service-call or diagnostic fee to send a technician out, and many credit it toward the repair if you go ahead. Ask what the fee is and whether it is credited, then ask for a written estimate that itemizes parts, labor, and any trip charge before you authorize the job.

5. 05

   Put the warranty term on the estimate

   Parts and labor are usually guaranteed for different lengths of time and the terms vary by company, so ask for both in writing rather than assuming. Ask specifically who pays for the return visit if the same fault comes back within the term.

6. 06

   Pay on completion, and keep the itemized invoice

   A deposit against a special-order part is normal; a large up-front payment for the whole job is not. Pay the balance once the appliance has been tested in front of you, and keep the itemized invoice — you will need the part number and the labor term for any warranty claim later.

The 2 companies on this page give addresses in 2 distinct ZIP codes — 75501 and 75503. A ZIP here is where the business is registered, not a limit on where it will drive.

Other Texas cities we cover

• Austin · Travis County8 pros
• Houston · Harris County7 pros
• Dallas · Dallas County5 pros
• San Antonio · Bexar County5 pros
• El Paso3 pros
• Georgetown3 pros
• Plano3 pros
• Spring2 pros
• Arlington1 pro
• Baytown1 pro
• Borger1 pro
• Burleson1 pro
• Cedar Hill1 pro
• Cleburne1 pro
• College Station1 pro
• Conroe1 pro
• Ennis1 pro
• Fort Worth1 pro
• Katy1 pro
• Lake Worth1 pro
• Lampasas1 pro
• Lewisville1 pro
• Mansfield1 pro
• McKinney1 pro
• Pearland1 pro
• Round Rock1 pro
• Sugar Land1 pro
• Webster1 pro